Over the past few decades, Single-Particle Analysis (SPA), in combination with cryo-transmission electron microscopy, has evolved into one of the leading technologies for structural analysis of biological macromolecules. It allows the investigation of biological structures in a close to native state at the molecular level. Within the last five years the achievable resolution of SPA surpassed 2°A and is now approaching atomic resolution, which so far has only been possible with Xray crystallography in a far from native environment. One remaining problem of Cryo-Electron Microscopy (cryo-EM) is the weak image contrast. Since the introduction of cryo-EM in the 1980s phase plates have been investigated as a potential tool to overcome these contrast limitations. Until now, technical problems and instrumental deficiencies have made the use of phase plates difficult; an automated workflow, crucial for the acquisition of 1000s of micrographs needed for SPA, was not possible. In this thesis, a new Zernike-type Phase Plate (PP) was developed and investigated. Freestanding metal films were used as a PP material to overcome the ageing and contamination problems of standard carbon-based PPs. Several experiments, evaluating and testing various metals, ended with iridium as the best-suited material. A thorough investigation of the properties of iridium PP followed in the second part of this thesis. One key outcome is a new operation mode, the rocking PP. By using this rocking-mode, fringing artifacts, another obstacle of Zernike PPs, could be solved. In the last part of this work, acquisition and reconstruction of SPA data of apoferritin was performed using the iridium PP in rocking-mode. A special semi-automated workflow for the acquisition of PP data was developed and tested. The recorded PP data was compared to an additional reference dataset without a PP, acquired following a conventional workflow.

Aquatic hyphomycetes are a polyphyletic group of saprotrophic fungi growing abundantly on submerged leaf litter. In stream ecosystems shaped by allochthonous leaf litter inputs, they play a central functional role as decomposers and food source for other organisms. Fungicides pose a threat to aquatic hyphomycetes and their functions, since these substances are inherently toxic to fungi and contaminate surface waters around the world due to their widespread use in agricultural and urban landscapes. While fungicides’ potential to reduce fungal diversity are discerned, the extent of impacts on biodiversity-ecosystem functioning relationships (B EF) remains unclear. This is partly attributed to methodological constraints in the detection and quantification of single aquatic hyphomycete species within microbial leaf-associated communities. The primary aim of this thesis was, therefore, (1) to assess the ecotoxicological impacts of fungicides on B-EF relationships in aquatic hyphomycete communities. To facilitate this, subordinate aims were to (2) develop DNA-based biomolecular tools (i.e., qPCR assays) to detect and to quantify the biomass of different aquatic hyphomycete species in mixed cultures and (3) to investigate the mechanisms underlying B-EF relationships in the absence of chemical stressors. In the course of this thesis, qPCR assays were developed for detection and species-specific biomass quantification of ten common aquatic hyphomycete species and successfully validated for application in eco( toxico )logical microcosm experiments. Via a systematic manipulation of fungal diversity, these assays allow the examination of B-EF relationships by assessments of deviations between observed and (monoculture-based) predicted activities in fungal mixed cultures. Taking advantage of these tools in a microcosm experiment, it was uncovered that leaf decomposition results from the additive activity of community members, even though functionally distinct species were present. Colonization dynamics are characterized by complex interactions. Colonization success of aquatic hyphomycetes is higher if co-occurring species are genetically and functionally distinct (i.e., complementary interactions). However, the co-occurrence of aquatic hyphomycete species does not necessarily result in a greater colonization success compared to monocultures, unless bacteria are present. Accordingly, the presence of other microbial groups such as bacteria may induce new fungal diversity-based feedback loops, which ultimately enable coexistence of aquatic hyphomycete species in the environment. Exposure to fungicides revealed substantial differences in sensitivities among aquatic hyphomycetes. The most productive species were able to cope with extremely high fungicide concentrations up to the mg/L-range. In assemblages containing these species, leaf decomposition was maintained under fungicide exposure. Yet, already at environmentally relevant fungicide concentrations, tolerant species displaced more sensitive ones, potentially affecting leaves’ nutritional quality for consumers. This thesis thus indicates that fungicide exposure poses a risk to stream food webs rather than the microbial leaf decomposition process per se.

SUMMARY Buildings and infrastructures characterize the appearance of our cultural landscapes and provide essential services for the human society. However, they inevitably impact the natural environment e.g. by the structural change of habitats. Additionally, they potentially cause further negative environmental impacts due to the release of chemical substances from construction materials. Galvanic anodes and organic coatings regularly used for corrosion protection of steel structures are building materials of particular importance for the transport infrastructure. In direct contact with a water body or indirectly via the runoff after rainfall, numerous chemicals can be released into the environment and pose a risk to aquatic organisms. Up to now, there is no uniform investigation and evaluation approach for the assessment of the environmental compatibility of building products. Furthermore, galvanic anodes and organic coatings pose particular challenges for their ecotoxicological characterization due to their composition. Therefore, the objective of the presented thesis was the ecotoxicological assessment of emissions from galvanic anodes and protective coatings as well as the development of standardized assessment procedures for these materials. The possible environmental hazard posed by the use of anodes on offshore installations was investigated on three trophic levels. To ensure a realistic and reliable evaluation, the experiments were carried out in natural seawater and under natural pH conditions. Moreover, the anode material and its main components zinc and aluminum were exposed while simulating a worst-case scenario. The anode material examined caused a weak inhibition of algae growth; no acute toxicity was observed on the luminescent bacteria and amphipods. However, an increase of aluminum and indium levels in the crustacean species was found. On the basis of these results, no direct threat has been identified for marine organisms from the use of galvanic aluminum anodes. However, an accumulation of metals in crustaceans and a resulting entry into the marine food web cannot be excluded. The environmental compatibility of organic coating systems was exemplarily evaluated using a selection of relevant products based on epoxy resins (EP) and polyurethanes. For this purpose, coated test plates were dynamically leached over 64 days. The eluates obtained were systematically analyzed for their ecotoxicological effects (acute toxicity to algae and luminescent bacteria, mutagenic and estrogenic effects) and their chemical composition. In particular, the EP-based coatings caused significant bacterial toxicity and estrogen-like effects. The continuously released 4-tert-butylphenol was identified as a main contributor to these effects and was quantified in concentrations exceeding the predicted no effect concentration for freshwater in all samples. Interestingly, the overall toxicity was not governed by the content of 4-tert-butylphenol in the products but rather by the release mechanism of this compound from the investigated polymers. This finding indicates that an optimization of the composition can result in the reduction of emissions and thus of environmental impacts - possibly due to a better polymerization of the compounds. Coatings for corrosion protection are exposed to rain, changes in temperature and sun light leading to a weathering of the polymer. To determine the influence of light-induced aging on the ecotoxicity of top coatings, the emissions and associated adverse effects of UV-irradiated and untreated EP-based products were compared. To that end, the investigation of static leachates was focused on estrogenicity and bacterial toxicity, which were detected in the classic microtiter plate format and in combination with thin-layer plates. Both materials examined showed a significant decrease of the ecotoxicological effects after irradiation with a simultaneous reduction of the 4-tert-butylphenol emission. However, bisphenol A and various structural analogues were detected as photolytic degradation products of the polymers, which also contributed to the observed effects. In this context, the identification of bioactive compounds was supported by the successful combination of in-vitro bioassays with chemical analysis by means of an effect-directed analysis. The presented findings provide important information to assess the general suitability of top coatings based on epoxy resins. Within the scope of the present study, an investigation concept was developed and successfully applied to a selection of relevant construction materials. The adaptation of single standard methods allowed an individual evaluation of these products. At the same time, the suitability of the ecotoxicological methods used for the investigation of materials of unknown and complex composition was confirmed and the basis for a systematic assessment of the environmental compatibility of corrosion protection products was created. Against the background of the European Construction Products Regulation, the chosen approach can facilitate the selection of environmentally friendly products and contributes to the optimization of individual formulations by the simple comparison of different building materials e.g. within a product group.

Studies have shown that runoff and spray-drift are important sources of nonpoint-source pesticide pollution of surface waters. Owing to this, public concern over the presence of pesticides in surface and ground water has resulted in intensive scientific efforts to find economical, yet environmentally sound solutions to the problem. The primary objective of this research was to assess the effectiveness of vegetated aquatic systems in providing buffering between natural aquatic ecosystems and agricultural landscape following insecticide associated runoff and spray-drift events. The first set of studies were implemented using vegetated agricultural ditches, one in Mississippi, USA, using pyrethroids (bifenthrin, lambda-cyhalothrin) under simulated runoff conditions and the other in the Western Cape, South Africa using the organophosphate insecticide, azinphos-methyl (AZP), under natural runoff and spray-drift conditions. The second set of studies were implemented using constructed wetlands, one in the Western Cape using AZP under natural spray-drift conditions and the other in Mississippi, USA using the organophosphate MeP under simulated runoff conditions. Results from the Mississippi-ditch study indicated that ditch lengths of less than 300 m would be sufficient to mitigate bifenthrin and lambda-cyhalothrin. In addition, data from mass balance calculations determined that the ditch plants were the major sink (generally > 90%) and/or sorption site for the rapid dissipation of the above pyrethroids from the water column. Similarly, results from the ditch study in South Africa showed that a 180 m vegetated system was effective in mitigating AZP after natural spray drift and low flow runoff events. Analytical results from the first wetland study show that the vegetated wetland was more effective than the non-vegetated wetland in reducing loadings of MeP. Mass balance calculations indicated approximately 90% of MeP mass was associated with the plant compartment. Ninety-six hours after the contamination, a significant negative acute effect of contamination on abundances was found in 8 out of the 15 macroinvertebrate species in both wetland systems. Even with these toxic effects, the overall reaction of macroinvertebrates clearly demonstrated that the impact of MeP in the vegetated wetland was considerably lower than in the non-vegetated wetland. Results from the constructed wetland study in South Africa revealed that concentrations of AZP at the inlet of the 134 m wetland system were reduced by 90% at the outlet. Overall, results from all of the studies in this thesis indicate that the presence of the plant compartment was essential for the effective mitigation of insecticide contamination introduced after both simulated and natural runoff or spray-drift events. Finally, both the vegetated agricultural drainage ditch and vegetated constructed wetland systems studied would be effective in mitigating pesticide loadings introduced from either runoff or spray-drift, in turn lowering or eliminating potential pesticide associated toxic effects in receiving aquatic ecosystems. Data produced in this research provide important information to reduce insecticide risk in exposure assessment scenarios. It should be noted that incorporating these types of best management practices (BMPs) will decrease the risk of acute toxicity, but chronic exposure may still be an apparent overall risk.

The transport of pesticides from agricultural land into surface waters via diffuse entry pathways such as runoff is a major threat to aquatic ecosystems and their communities. Although certain risk mitigation measures are currently stipulated during pesticide product authorisation, further approaches might be needed to manage hot spots of pesticide exposure. Such a management is, for example, required by the European Union- directive for the sustainable use pesticides (2009/128/EC). The need for mitigation measures was investigated within the present thesis at stream sites draining an arable and a vineyard region in Germany by characterising pesticide exposure following edge-of-field runoff and (expected) effects on the aquatic macroinvertebrates. The results of these field studies showed, that streams in both regions were exposed to pesticide concentrations suggesting effects on the macroinvertebrate community. In the arable region the observed toxicity was mainly attributed to the insecticides lambda-cyhalothrin (in the water-phase samples) and alpha-cypermethrin (in the suspended particle samples), whereas in the vineyard region fungicides were most important. Furthermore stream water and suspended particles sampled in the vineyard region showed critical copper concentrations, which might cause ecotoxicological effects in the field. In addition to pesticide exposure, in the arable region also the effects on aquatic macroinvertebrates were assessed in the field. Generally, invertebrate fauna was dominated by pesticide-tolerant species, which suggested a high pesticide exposure at almost all sites. The elevated levels of suspended particle contamination in terms of maximum toxic units per sample (logTUMax > -2) reflect also this result. At two sites that received high aqueous-phase entries of the insecticide lambda-cyhalothrin (logTUMax > -0.6), the abundance and number of sensitive species (indicated by the SPEcies At Risk index) decreased during the pesticide application period. In contrast, at sites characterised by low water-phase toxicity (logTUMax < -3.5), no acute significant negative effects on macroinvertebrates were observed. In conclusion these data showed that in both regions the implementation of risk mitigation measures is needed to protect the aquatic communities. To mitigate runoff-related pesticide entries, riparian buffer strips are often recommended. However, the mitigating influence with increasing buffer strip width could not be demonstrated for riparian buffers which were already present in the arable and vineyard region. This result was attributed in the vineyard region to the high number of paved field paths associated with artificial erosion rills, which concentrate and rapidly transport receiving edge-of-field runoff in stream direction. Consequently the pesticide reduction efficiency of buffer strips is considerably reduced. We assumed that a similar process occurred in the arable region, due to a high number of erosion rills, which complicate a laminar sheet flow of edge-of-field runoff through the riparian buffer strip. Additionally also the presence of ephemeral drainage ditches, which led surface runoff from the agricultural fields to the streams may have contributed to observed pesticide entries despite wide buffers. Effective risk mitigation measures should address these identified most important input pathways in the study areas. As possible measures the implementation of grassed field paths and vegetated ditches or wetlands were suggested. In general also the improvement of currently present riparian buffer strips regarding their efficiency to reduce pesticide runoff entries should be taken into account. In conclusion the results of the field studies underline the importance that risk mitigation measures are identified specifically for the respective pollution situation in stream catchments. To facilitate this process, a user guide was developed within the present thesis for identifying appropriate mitigation measures at high-risk sites. Based on a survey of exposure relevant landscape parameter a set of risk mitigation measures is suggested that focus on the specific pollution situation. Currently the guide includes 12 landscape- and six application-related measures and presents an overview of these measures" efficiency to reduce pesticide entries via runoff and spray drift, their feasibility and expected acceptability to farmers. Based on this information the user can finally choose the mitigation measures for implementation. The present guide promotes the practical implementation of appropriate risk mitigation measures in pesticide-polluted streams, and thus the protection of aquatic stream communities against pesticide entries.

Unsere Welt und die technischen und naturwissenschaftlichen Erkenntnisse verändern sich aktuell sehr schnell. Dies betrifft auch die naturwissenschaftliche Forschung und erfordert vermehrten Einsatz der Wissenschaftskommunikation und der Bildung. Ein Instrument der Wissenschaftskommunikation und eine Erweiterung des schulischen Unterrichts kann die Beteiligung von Freiwilligen bei wissenschaftlichen Arbeiten sein, welches auch als Citizen Science (CS) bezeichnet wird. CS Projekte erfreuen sich einer wachsenden Beliebtheit, unter anderem von Schulen (Burger, 2016). Dabei werden unter anderem die Förderung des Kontextwissens, der Scientific Literacy, der Umwelteinstellung und des –verhaltens versprochen (Peter et al., 2019). Interventionsstudien zu den Bildungspotentialen kommen jedoch zu unterschiedlichen Ergebnissen (Gommermann & Monroe, 2012; Turrini et al., 2018). Diese inkonsistenten Ergebnisse der Studien können auf die unterschiedliche Gestaltung der einzelnen evaluierten CS Projekte zurückgeführt werden. Es wird angenommen, dass Teilnehmende, die in mehr Schritten des wissenschaftlichen Prozesses eingebunden werden, ein größeres Bildungspotential haben, als Teilnehmende, die nur in wenige Schritte eingebunden werden (Burger, 2016; Shirk & Bonney, 2018). Bonney, Ballard et al. (2009) haben dazu ein dreistufiges Modell entwickelt. Das Modell wird unter anderem auch von Shirk et al. (2012) und Jordan et al. (2015) unterstützt, ist jedoch bezüglich der Lernwirksamkeit nicht empirisch überprüft (Edwards et al., 2018; Jordan et al., 2015). Deswegen schließt die Forschungsfrage dieser Studie hier an: Unter welchem Partizipationsansatz sind die Lerneffekte in einem CS Projekt am größten für Schülerinnen und Schüler? Um diese Frage zu beantworten, wurde ein CS Projekt mit drei Experimentalgruppen geplant und durchgeführt. Insgesamt nahmen 199 Schülerinnen und Schüler an dem Projekt teil. Innerhalb der Interventionsstudie wurden die Schülerinnen und Schüler zu drei Testzeitpunkten zur Umwelteinstellung und -verhalten, Nature of Science, Einstellung zur Wissenschaft und dem Kontextwissen befragt. Die Analysen über die Messzeitpunkte zeigen keine statistisch signifikanten Einflüsse der Experimentalgruppen auf die abhängigen Variablen. Jedoch ist die Teststärke bei allen Tests zu gering, um abschließende Aussagen über die Annahmen zu treffen. Wird jedoch die generelle Wirkung der Intervention betrachtet, zeigen sich signifikante Effekte auf alle Schülerinnen und Schüler, unter anderem steigt das Verständnis über Nature of Science. Diese Ergebnisse stimmen mit früheren Schlussfolgerungen von Phillips (2017), Phillips et al. (2019) und Del Bianco (2018) überein, die ebenfalls Zweifel an dem Modell von Bonney, Ballard et al. (2009) äußerten. Innerhalb dieses CS Projektes konnte sich keiner der drei Partizipationsansätze bezüglich des Bildungspotential für Schülerinnen und Schüler hervorheben lassen. Jedoch ist diese Studie unter anderem durch die geringe Teststärke limitiert und endgültige Aussagen bedürfen weiterer systematischer Forschung.

The biodegradable polymers polylactic acid (PLA) and polyhydroxybutyrate (PHB) produced from renewable raw materials were coated with hydrogenated amorphous carbon layers (a-C:H) at different deposition angles with various thicknesses as part of this thesis. Similar to conventional polymers, biopolymers often have unsuitable surface properties for industrial purposes, e.g. low hardness. For some applications, it is therefore necessary and advantageous to modify the surface properties of biopolymers while retaining the main properties of the substrate material. A suitable surface modification is the deposition of thin a-C:H layers. Their properties depend essentially on the sp² and sp³ hybridization ratio of the carbon atoms and the content of hydrogen atoms. The sp²/sp³ ratio was to be controlled in the present work by varying the coating geometry. Since coatings at 0°, directly in front of the plasma source, contain a higher percentage of sp³ and indirectly coated (180°) a higher amount of sp², it is shown in this work that it is possible to control the sp²/sp³ ratio. For this purpose, the samples are placed in front of the plasma source at angles of 0, 30, 60, 90, 120, 150 and 180° and coated for 2.5, 5.0, 7.5 and 10.0 minutes. For the angles 0°, the layer thicknesses were 25, 50, 75 and 100 nm. The a-C:H layers were all deposited using radio-frequency plasma-enhanced chemical vapor deposition and acetylene as C and H sources after being pretreated with an oxygen plasma for 10 minutes. Following the O₂ treatment and the a-C:H deposition, the surfaces are examined using macroscopic and microscopic measurement methods and the data is then analyzed. The surface morphology is recorded using scanning electron microscopy and atomic force microscopy. In addition, data on the stability of the layer and the surface roughness can be collected. Contact angle (CA) measurements are used to determine not only the wettability, but also the contact angle hysteresis by pumping the drop volume up and down. By measuring the CA with different liquids and comparing them, the surface free energy (SFE) and its polar and disperse components are determined. The changes in barrier properties are verified by water vapor transmission rate tests (WVTR). The chemical analysis of the surface is carried out on the one hand by Fourier transform infrared spectroscopy with specular reflection and on the other hand by synchrotron-supported techniques such as near-edge X-ray absorption fine structure and X-ray photoelectron spectroscopy. When analyzing the surfaces after the O₂ treatment, which was initially assumed to serve only to clean and activate the surface for the a-C:H coating, it was found that the changes were more drastic than originally assumed. For example, if PLA is treated at 0° for 10 minutes, the roughness increases fivefold. As the angle increases, it decreases again until it returns to the initial value at 180°. This can be recognized to a lesser extent with PHB at 30°. For both polymers, it can be shown that the polar fraction of the SFE increases. In the WVTR, a decrease in permeability can be observed for PLA and an increase in the initial value for PHB. The chemical surface analysis shows that the O₂ treatment has little effect on the surface bonds. Overall, it can be shown in this work that the O₂ treatment has an effect on the properties of the surface and cannot be regarded exclusively as a cleaning and activation process. With direct a-C:H coating (at 0°), a layer failure due to internal stress can be observed for both PLA and PHB. This also occurs with PHB at 30°, but to a lesser extent. Permeability of the polymers is reduced by 47% with a five-minute coating and the layer at 10.0 minutes continues to have this effect despite cracks appearing. The application of a-C:H layers shows a dominance of sp³ bonds for both polymer types with direct coating. This decreases with increasing angle and sp² bonds become dominant for indirect coatings. This result is similar for all coating thicknesses, only the angle at which the change of the dominant bond takes place is different. It is shown that it is possible to control the surface properties by an angle-dependent coating and thus to control the ratio sp²/sp³.

This dissertation introduces a methodology for formal specification and verification of user interfaces under security aspects. The methodology allows to use formal methods pervasively in the specification and verification of human-computer interaction. This work consists of three parts. In the first part, a formal methodology for the description of human-computer interaction is developed. In the second part, existing definitions of computer security are adapted for human-computer interaction and formalized. A generic formal model of human-computer interaction is developed. In the third part, the methodology is applied to the specification and verification of a secure email client.

Hintergrund: Veränderte gesetzliche Rahmenbedingungen in der stationären Altenhilfe, die demografische Entwicklung mit dem steigenden Bedarf an Pflegekräften einerseits und die Tatsache, dass immer weniger Menschen aufgrund des Images des Berufes und der Arbeitsbedingungen in der Pflege tätig sein wollen andererseits, machen es notwendig neue Wege zu suchen. Die Träger im Sozial- und Gesundheitswesen sind gefordert, Konzepte zu entwickeln, die ihre Wirtschaftlichkeit sichern, gleichzeitig aber auch den Belastungen und der Unzufriedenheit von Mitarbeitenden entgegenwirken. Es braucht Gestaltungsräume, um Lösungen im Konflikt zwischen Anspruch und Machbarkeit zu finden und so dem alltäglichen Stress, der Mitarbeiterfluktuation und dem drohenden Leistungsabfall entgegenzuwirken. Durch das Praxisprojekt eines sozial-karitativen Trägers zur Implementierung einer ´Konstruktiven Konfliktkultur´ in einer stationären Altenhilfeeinrichtung sollte eine Organisationskultur geschaffen werden, in der Konflikte offen angesprochen werden, eine Offenheit für Veränderungsprozesse entsteht, Belastungen reduziert und die Mitarbeitenden an die Organisation gebunden werden. Dazu wurden drei pädagogische Interventionen entwickelt, durch die die Mitarbeitenden und die Führungskräfte in ihrer Konfliktfähigkeit geschult werden sollten. Methode: Die wissenschaftliche Begleitung dieses Praxisprojektes fand als Evaluationsstudie statt. Zu drei Erhebungszeitpunkten wurde eine repräsentative Mitarbeitergruppe dieser Einrichtung zu den Themen Konflikterleben, Führungsverhalten, Macht/ Regeln und Veränderungen durch qualitative Leitfadeninterviews befragt. Die Auswertung und Analyse der Daten erfolgte im Sinne der qualitativen Inhaltsanalyse nach Mayring und floss ein in eine formative Prozessevaluation der einzelnen Interventionen und einer summativen Effektevaluation zu Bewertung der Zielerreichung des Projektes. Ergebnis: Die einzelnen Interventionen des Projektes konnten nicht dazu beitragen, dass eine ´Konstruktiven Konfliktkultur´ nachhaltig entwickelt werden konnte. Zwar gab es in der Bewusstseinsspanne des Projektes einen expliziten Wissensgewinn, jedoch mehr bei den Führungskräften als bei den Mitarbeitenden. Die Führungskräfte sahen im Projekt einen Gewinn, für einen Teil der Mitarbeitenden war es sogar Zeitverschwendung. Anhand der Ergebnisse lassen sich drei Merkmale herauskristallisieren, die kennzeichnend sind für die zugrundeliegenden Denk-, Urteils-, und Handlungsstrukturen in sozialen Organisationen im Umgang mit Konflikten: Konflikte sind nicht wahrnehmbare Konstrukte der Alltagswelt. Sie manifestieren sich aufgrund fehlender Legitimation in Überforderung und eine ´Konstruktiven Konfliktkultur´ kann nicht auf das Wissen Einzelner aufbauen, sondern benötigt verbindliche Handlungsstrukturen für alle Organisationsmitglieder gleichermaßen. Ergebnisinterpretation: Durch die Einbeziehung wissenssoziologischer und konfliktsoziologischer Theorien und deren Einordnung in Institutionen – und Organisationstheorien konnten die Ergebnisse diskutiert und neue Erkenntnisse über Konflikte in Organisationen, die sich in drei Spannungsfeldern zeigen, gewonnen werden. Die Spannungsfelder bewegen sich zwischen dem Konflikt als nicht-wahrnehmbarem Alltagsphänomen auf der einen Seite und einer manifestierten Belastung auf der anderen Seite, dem Gewohnheitswissen im alltäglichen Umgang einerseits und einem fehlenden Handlungswissen andererseits, einer funktional-positiven Sicht hier und einer dysfunktional-negativen Sicht dort. Anhand dieser Spannungsfelder kann die Konfliktmentalität und ihre Entstehung und auch die Möglichkeit ihrer Veränderbarkeit reflektiert und können Erfolgsfaktoren für die Implementierung einer ´Konstruktiven Konfliktkultur´ entwickelt werden. Schlussfolgerung: Wissen, Legitimation und Institutionalisierung und die Stärkung der Wahrnehmungen sind der Schlüssel für die Veränderung der Konfliktmentalität in sozialen Organisationen. Nachhaltigkeit erhält die Thematik aber erst, wenn alle Organisationsmitglieder eine gewisse Handlungsnotwendigkeit für sich erkennen. Aktuell steht die Organisationsentwicklung für den expliziten Veränderungswillen von Management, der jedoch auf ein gewisses Beharrungsvermögen von Mitarbeitenden trifft.

The research described in this thesis was designed to yield information on the impact of particle-bound pesticides on organisms living in the interface between sediment and water column in a temporarily open estuary (TOCEs). It was hypothesized that natural variables such as salinity and temperature and anthropogenic stressors such as particle-bound pesticides contribute to the variability of the system. A multiple line of evidence approach is necessary due to the variability in sediment type, contaminant distribution and spatial and temporal variability within the ecosystem in particular within TOCEs. The first aim of this thesis was to identify which particle-bound pesticides are important to the contamination of the Lourens River estuary (Western Cape, South Africa), taking into account their environmental concentrations, physico-chemical and toxicological properties (Exposure assessment). The second aim was to identify spatial and temporal variations in particle bound pesticide contamination, natural environmental variables and benthic community structure (effect assessment). The third aim was to test the hypothesis: "does adaptation to fluctuating salinities lead to enhanced survival of the harpacticoid copepod Mesochra parva when exposed to a combination of particle associated chlorpyrifos exposure and hypo-osmotic stress during a 96 h sediment toxicity test?" The last aim was to identify the driving environmental variables (including natural and anthropogenic stressors) in a "natural" (Rooiels River) compared to a "disturbed" (Lourens River) estuary and to identify if and how these variables change the benthic community structure in both estuaries. Data produced in this research thus provide important information to understand the impact of pesticides and its interaction with natural variables in a temporarily open estuary. To summarise, this study indicated, by the use of the multi-evidence approach, that the pesticides endosulfan and chlorpyrifos posed a risk towards benthic organisms in a temporarily open estuary in particular during spring season. Furthermore an important link between pesticide exposure/ toxicity and salinity was identified, which has important implications for the management of temporarily open estuaries.